Das Filter Blog

How to Roll an L Joint (L Plate), Step by Step

By Das Filter Team6 min read

A cone-shaped joint with a paper crutch resting on cannabis buds against a pale blue background

Quick answer: Take two papers. Lick about half of the second paper's gum strip and stick it at a right angle across one end of the first paper, so they form an L. Put your tip at the other end, spread flower in a line that gets thicker toward the L, then roll it like a cone: tuck at the tip, roll up, and seal along the first paper's gum. Tear off extra paper at the wide end, pack it and twist it shut.

An L is a bigger joint for when one paper isn't enough and you don't have king size papers. It rolls into a long cone. The two tricky parts are joining the papers and closing the wide end.

What you need

ItemWhy
Two rolling papers, same sizeThe L. Single wide or 1 1/4 are common.
A filter tipThe narrow mouth end. A 7mm tip suits 1 1/4 papers.
Ground flowerMore than a single joint, since the L has more paper
A tray or matYou'll spill some while you shape it
A poker or penTo pack the wide end

Step 1: Make the L

  1. Lay the first paper flat in front of you, gum strip up and along the top edge, away from you. This is the bottom of the L.
  2. Turn the second paper on its side, so its gum strip runs up and down along its left edge, gum side down.
  3. Lick only the bottom half of that gum strip.
  4. Lay that edge over the right-hand end of the first paper, bottom edges lined up, overlapping only by the width of the gum strip. The second paper now stands up above the first at a right angle. Press the join flat.
  5. Give the join half a minute or so to set before you fill it.

Prefer the wide end on the left? Build it the other way round: second paper on the left, gum strip along its right edge.

Step 2: Set the tip

Put the tip at the end of the first paper away from the L. Keep it flush with the edge.

Step 3: Fill it

Spread flower along the crease from the tip to the L. Start thin at the tip and get gradually thicker toward the wide end, like a long cone. Don't fill the upright part of the second paper; that's extra paper for wrapping around the wide end.

Step 4: Shape it

Pinch the paper and roll it back and forth to pack the flower into a cone shape: narrow at the tip, wide at the L end. Take your time. An even cone burns better.

Step 5: Tuck and roll

Start at the tip end. Tuck the bottom edge of the first paper over the flower and under, using the tip as a guide, then work the tuck along toward the wide end. The tuck at the wide end will be looser because the cone is wider there. Roll up toward the gum strip.

Step 6: Seal

Lick the first paper's gum strip lightly and press it closed from the tip end out. At the wide end, the second paper wraps around and has no gum of its own along that edge. Tear off any extra paper beyond one full wrap, then dampen the edge lightly and press it down, or cut a thin strip off a spare paper's gum and use it as a patch.

Step 7: Pack and twist

Tap the L tip-down to settle the flower. Pack the wide end lightly with a poker, top it up if it's loose, and twist the extra paper closed.

Common problems

ProblemLikely causeFix
Papers come apartJoin too wet or not setLick lightly and wait before filling
Wide end flaps openNo gum thereTear off extra paper; patch with a gum strip
Burns down one sideUneven fill or tuckEven out the cone; see why does my joint canoe
Hard to drawPacked too tightSee why is my joint not pulling
Too much paper tasteLots of overlapTear off the extra before sealing

L joint or king size paper?

An L is a workaround. If you can get king size papers, a king size joint is the simpler way to roll a bigger joint, with one paper and one seam. The L is handy when all you have are small papers, or if you like the cone shape. For a straight cone from one paper, see how to roll a cone.

Do you need a tip?

No, but it helps here. A long cone is floppy at the narrow end; a tip gives you something firm to start the tuck around and keeps the mouth end open. If you're rolling 1 1/4 papers, our Midway 7mm tips fit. If you'd rather skip it, see how to roll a joint without a filter.

New to rolling? Start with how to roll a joint, then try the L.

Frequently asked questions

What is an L joint?

A joint rolled from two papers stuck together in an L shape. The second paper adds length and width at one end, so it rolls into a long cone that holds more than a single paper.

Why is it called an L plate?

Because of the L the two papers make before rolling, the same shape as the L plate UK learner drivers display. The name is most common in the UK.

What papers do you need for an L?

Two regular papers, usually the same size. Single wide or 1 1/4 papers are common. King size papers make a very long L.

Which end does the tip go in?

The end away from the second paper. That end stays narrow, and the end with the extra paper becomes the wide end you light.

Is an L joint hard to roll?

It's harder than a regular joint because the paper is a strange shape and the wide end has no gum of its own. If you can roll a cone, you can roll an L with a little practice.


Products are for adults 21+.

Shop Das Filter

Products in this post

Activated carbon filter tips, papers and rolling gear, made and shipped from Austin, TX.

See all products Buying for a shop? Wholesale